SWP-WRC3.1 CAN ratti paneli / Steering Wheel membrane panel

• 1 kpl CAN 
• 2.0B protocol
  
• Väylä nopeus valittavissa: 1 Mbit/s, 500 kbit/s, 250 kbit/s, 200 kbit/s, 125 kbit/s ja 100 kbit/s
• 120 Ω päätevastus
  
• Oikosulkusuojaus
  
• 1 kpl digitaalinen sisääntulo
• Sisääntulovastus: 4.7 kΩ (5V pull-up)
• Analogia anti aliasing filter
• 12 kpl painonappeja, taustavalot ja 2 kpl LED valoja
• Napin tila lähetetään CAN viestinä
• 4 kpl kiertokytkimiä, tila lähetetään CAN viestinä
• 2 kpl On–Off drivers
• High side driver Vbattery, up to 1 A
• Output voltage reread
• Linear current limitation
• Oikosulkusuoja
• Ylikuorma ja lämpötila hälytys ja suoja
• 2 kpl LED tilaväriä napeissa (punainen – vihreä)
• Aktivointi CAN viesteinä
• Kaikki LED velot voidaan määritellä napin asennosta riippumatta
• LED valon kirkkaus määriteltävissä ohjelmalla
• 6 kpl väri LED:ä kiertokytkimissä (8 kpl optionat)
• LED värejä voidaan muokata tilauksesta
  
• Näyteresoluution 10 bit
• Lämpötila-alue: -40 / +120 °C
• 2 kpl High side switch outputs voltage reread
• Jännite partition 20 mV
• Analogia anti aliasing filter
  
• Symbolitarrat tilauksesta 90 €, sis. graafisen suunnittelun asiakkaalle
• Mitat: 
• Johdon kanssa: 209 x 153 x 29 mm
• Kiertokytkimien kanssa: 209 x 153 x 42 mm
• 20 cm johto ASL606-05PB liittimellä,. Vastaliitin (ASL106-05SB) tilattavissa erikseen. 
• Runko billet alumiini ja ABS kuori
• IP65 vesitiivis
• Paino 325 g

Membrane Steering Wheel Panel

Note! FIA regulation doesn't allow modification of steering wheel.

Designed for Sabelt 330 mm steering wheel.

1 CAN line

• 1 Mbit/s throughtput data rate
• Selectable bus speed: 1 Mbit/s, 500 kbit/s, 250 kbit/s, 200 kbit/s, 125 kbit/s and 100 kbit/s
• 2.0B protocol
  
• Software selectable 120 Ω terminator
• Protection against short circuit to ground and battery

1 Digital input for programming enable (ENCP)

• Input resistance: 4.7 kΩ (5V pull-up)
• Protection against short circuit to Vbattery.

12 Keyboard buttons

• With backlighting
• With integrated 2 – color gauge LED
• Button state transmitted on CAN

4 Mechanical rotary switches

• Compact design – PCB mounted
• Switch state transmitted on CAN
• Mechanical endless with electrical „smart stop“ feature
• Number of positions adjustable by SW

2 On–Off drivers

• High side driver Vbattery, up to 1 A
• Output voltage reread
• Linear current limitation
• Protection against short circuit to ground
• Overload, over temperature feedback and protection

12 Gauge LEDs

• 2 color state (red – green)
• Integrated in keyboard buttons
• Activation received from CAN
• Each LED controlled independently from button
• LED color adjustable by SW within red – green scale
• Brightness adjustable by SW

4 Status Gauge LED at rotary groups

• 6 single colour LEDs in each rotary group (8 optional on request)
• Each LED group has its independent control – internally (by firmware) or via CAN
• LED colors can be modified on request (HW modification)

1 Internal temperature

• Sampling resolution: 10 bits
• Temperature range: -40 / +120 °C

2 High side switch outputs voltage reread

• Sampling resolution: 10 bits
• Voltage partition 20 mV
• Analogue anti aliasing filter

Preliminary overall dimensions

• With cable: 209 x 153 x 29 mm
• Including rotary knobs: 209 x 153 x 42 mm
• 20 cm cable with ASL606-05PB connector. Mating connector (ASL106-05SB) available separately. 

Enclosure

• Machined aluminum / ABS cover
• IP grade  IP65

Weight (without steering wheel)

• approx 325 g

Panel mounting on steering wheel

• Requirements on the mounting system (apart of fixing function)
• maximum protection of panel when handling of the car
• minimum added weight
• simple steering column cable
• quick mounting and dismounting from steering wheel (steering wheel arms cannot be modified - FIA WRC regulation)
• Rear cover shaped to be centered on steering wheel – actually designed for Sabelt Ø330 mm and larger, can be adjusted on request.
• Fixing on steering wheel by tie-rap fasteners

Keyboard layouts, shape

• Layouts (button colors and symbols) can be modified to the customer requirements
• Standard layout is supplied with empty fields
• Sticker set 90 € is supplied with special order. Price includes graphic designed according to customer request.
• Larger quantities can be supplied with graphics on membrane applied by seriography
• Relief of buttons can be heighten by applying silicone caps on the top of the buttons (height upto cca 1.5 mm)

Tremondi push button panels are programmed with  Peak CAN interface.