CANchecked MFD15 monitoiminäyttö / multifunction display
OMINAISUUDET
- 52 mm halkaisijan OLED näyttö
- Ohjelmoitavissa ohjainyksiköille ja OBD2 diagnostiikkaväylälle
- 4 kpl analogia 0-5 V jännitekanavia
- Varoituksille määriteltävät raja-arvot
- Min ja max arvot antureille
- Kahden pisteen kalibrointi
- Integroitu LED-vaihtovalo
- 8 kpl näyttötyyppejä
- Äänihälytys
- Pop-up hälyytykset
Tuetut ohjainyksiköt:
- Trijekt (Premium, Bee, trigifant) - trijekt plus rajoituksin
- Megasquirt 2 ja 3
- K-Data KDFI
- UMC1 / UMC2
- Ecumaster EMU Black ja Classic (CAN-väylä adapterin kanssa)
- van Kronenburg KMS MD35 ja MP25 (CAN-väylä adapterin kanssa) - VAG (VW / Audi / Seat)
- Motorsport Electronics ME221 / ME442 (CAN Bus)
- LinkECU
- MaxxECU
- Motec
- SCS Delta
- BMW E46 Can Bus Protocol
- VW / Audi Can Bus Protocol
- OBD2 Can Bus (250 / 500kbit 11 / 29bit)
- Adapterin kanssa:
- VEMS
- ME221
-
Jos ohjainyksikköäsi ei ole mainittu listalla, ota yhteyttä
MFD15 toimitetaan seuraavilla varusteilla:- Näyttö MFD15
- Kiertokytkin 0.5 m johdolla
- 12 V virransyöttö ja näytön päivitysjohto
- MicroUSB data johto päivityksille
- Liitin analogia ja CAN-väylälle
- 20 cm CAN-väylä johto CAN-väylälle ja analogi signaaleille
- Liitin pinnejä
-
OBD2 LIITYNTÄ
OBD2 ohjelma on kehitetty lukemaan data OBD2 CAN datasta. CAN-väylänopeus pitää valita tapauskohtaisesti (250kbit tai 500kbit). 11bit ja 29bit tunnisteet toimivat automaattisesti. Seuraavat arvot voidaan lukea:
- RPM
- Moottorin kuorma
- Bensan paine
- Ahtopaine (MAP)
- Ajoneuvon nopeus
- Sytytysennakko
- Imuilman lämpötila
- Ilmamassa (MAF)
- Öljyn lämpötila
- Bensan paine
- Veden lämpötila
- Lambda 1-8
- Anturi 1
- Anturi 2
- Anturi 3
- Anturi 4
KEY FEATURES
- 52 mm diameter OLED display
- Programmable control units and OBD2 connection
- 4 analog inputs for additional sensors
- freely definable warning thresholds per sensor
- Min and max warning values per sensor
- 0-5 V sensor with 2-point calibration
- Integrated shift light LED - freely configurable
- 8 different display types
- Beep: A tone is emitted if the "min / max warning value" is exceeded or not reached
- Popup: If the "min / max warning value" is exceeded or not reached, a popup window is displayed
Supported control units:
- Trijekt (Premium, Bee, trigifant) - trijekt plus with restrictions
- Megasquirt 2 and 3
- K-Data KDFI
- UMC1 / UMC2
- Ecumaster EMU Black and Classic (with CAN bus adapter)
- van Kronenburg KMS MD35 and MP25 (with CAN bus adapter) - VAG (VW / Audi / Seat)
- Motorsport Electronics ME221 / ME442 (CAN bus)
- LinkECU
- MaxxECU
- Motec
- SCS Delta
- BMW E46 Can Bus Protocol
- VW / Audi Can Bus Protocol
- OBD2 Can Bus (250 / 500kbit 11 / 29bit)
- With serial adapter:
- VEMS
- ME221
If your control unit is not listed, please contact us
The MFD15 is delivered with:
- Display
- Rotary knob with 0.5m connection cable
- Adapter cable for connecting 12V and for updating the display
- Micro-USB data cable for updates
- Connector for analog inputs and CAN bus
- 20 cm pre-crimped connection cable for CAN bus, analog inputs, 5V and sensor ground
- Pins to crimp yourself
OBD2 CONNECTION
We have developed our own firmware for the MFD15, which queries data directly via the OBD2 CAN bus. You have to set the speed (250kbit or 500kbit) yourself. The display also recognizes 11bit and 29bit identifiers automatically.
With our OBD plug and play cable, the connection is made directly to the OBD socket. In addition, only the 12V supply has to be tapped with the enclosed fuse adapter. The following values are read:
- RPM
- Engine load
- Fuel Pressure
- Boost pressure (MAP)
- Vehicle speed
- Ignition angle (IgnAng)
- Intake temperature (IAT)
- Air mass (MAF)
- Oil temperature (OilTemp)
- Fuel pressure relative to inlet vacuum (FuelRail)
- Water temperature (CLT)
- Lambda 1-8
- Cat temperature bank1 sensor 1 (CatTemp1)
- Cat temperature bank1 sensor 2 (CatTemp2)
- Cat temperature bank2 sensor 1 (CatTemp3)
- Cat temperature bank2 sensor 2 (CatTemp4)